If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by Mag on August 15, 2008, 6:40 am
Hi
If i connect the C3524XL to a Cisco 6500 with a classic
RJ45 cable, i don't have the link. If i use a crossover cable, i have
the link.
I think's that C3524/6500 don't have auto mdi.
Anyone know if i can said by the cisco IOS that the port are connected
to another switch without a crossover cable ? "MDI by software"
thanks
mag
|
|
Posted by headsetadapter.com on August 15, 2008, 6:51 am
Hi Mag,
Catalyst 3524XL definitely do not have MDIX capablitiy for the ports (you
can confirm it with "show interface capability" command). Catalyst 6500 has
it on *some* blades, but you may need to enable it (it's off by default).
Good luck,
Mike
CCNP, CCDP, CCSP, CCVP, MCSE W2K, MCSE+I, Security+, etc.
CCIE Voice (in progress), CCIE R&S (next)
------
Headset Adapters for Cisco IP Phones
www.ciscoheadsetadapter.com
www.headsetadapter.com
> Hi
> If i connect the C3524XL to a Cisco 6500 with a classic
> RJ45 cable, i don't have the link. If i use a crossover cable, i have the
> link.
> I think's that C3524/6500 don't have auto mdi.
> Anyone know if i can said by the cisco IOS that the port are connected
> to another switch without a crossover cable ? "MDI by software"
> thanks
> mag
|
|
Posted by Mag on August 15, 2008, 7:24 am
Thanks for your answer,
do you know the process for put it "On" on the cisco 6500 ?
Thanks
headsetadapter.com a écrit :
> Hi Mag,
>
> Catalyst 3524XL definitely do not have MDIX capablitiy for the ports (you
> can confirm it with "show interface capability" command). Catalyst 6500 has
> it on *some* blades, but you may need to enable it (it's off by default).
>
> Good luck,
>
> Mike
> CCNP, CCDP, CCSP, CCVP, MCSE W2K, MCSE+I, Security+, etc.
> CCIE Voice (in progress), CCIE R&S (next)
> ------
> Headset Adapters for Cisco IP Phones
> www.ciscoheadsetadapter.com
> www.headsetadapter.com
>
>
>
>> Hi
>> If i connect the C3524XL to a Cisco 6500 with a classic
>> RJ45 cable, i don't have the link. If i use a crossover cable, i have the
>> link.
>> I think's that C3524/6500 don't have auto mdi.
>> Anyone know if i can said by the cisco IOS that the port are connected
>> to another switch without a crossover cable ? "MDI by software"
>> thanks
>> mag
>
>
|
|
Posted by Trendkill on August 15, 2008, 7:30 am
> Thanks for your answer,
> do you know the process for put it "On" on the cisco 6500 ?
> Thanks
> headsetadapter.com a =E9crit :
> > Hi Mag,
> > Catalyst 3524XL definitely do not have MDIX capablitiy for the ports (y=
ou
> > can confirm it with "show interface capability" command). Catalyst 6500=
has
> > it on *some* blades, but you may need to enable it (it's off by default=
).
> > Good luck,
> > Mike
> > CCNP, CCDP, CCSP, CCVP, MCSE W2K, MCSE+I, Security+, etc.
> > CCIE Voice (in progress), CCIE R&S (next)
> > ------
> > Headset Adapters for Cisco IP Phones
> >www.ciscoheadsetadapter.com
> >www.headsetadapter.com
> >> Hi
> >> If i connect the C3524XL to a Cisco 6500 with a classic
> >> RJ45 cable, i don't have the link. If i use a crossover cable, i have =
the
> >> link.
> >> I think's that =A0C3524/6500 don't have auto mdi.
> >> Anyone know if i can said by the cisco IOS that the port are connected
> >> to another switch without a crossover cable ? "MDI by software"
> >> thanks
> >> mag
On the cat side I think it is : set port auto-mdix enable. Not sure
on the native side.
|
|
Posted by Trendkill on August 15, 2008, 7:31 am
> > Thanks for your answer,
> > do you know the process for put it "On" on the cisco 6500 ?
> > Thanks
> > headsetadapter.com a =E9crit :
> > > Hi Mag,
> > > Catalyst 3524XL definitely do not have MDIX capablitiy for the ports =
(you
> > > can confirm it with "show interface capability" command). Catalyst 65=
00 has
> > > it on *some* blades, but you may need to enable it (it's off by defau=
lt).
> > > Good luck,
> > > Mike
> > > CCNP, CCDP, CCSP, CCVP, MCSE W2K, MCSE+I, Security+, etc.
> > > CCIE Voice (in progress), CCIE R&S (next)
> > > ------
> > > Headset Adapters for Cisco IP Phones
> > >www.ciscoheadsetadapter.com
> > >www.headsetadapter.com
> > >> Hi
> > >> If i connect the C3524XL to a Cisco 6500 with a classic
> > >> RJ45 cable, i don't have the link. If i use a crossover cable, i hav=
e the
> > >> link.
> > >> I think's that =A0C3524/6500 don't have auto mdi.
> > >> Anyone know if i can said by the cisco IOS that the port are connect=
ed
> > >> to another switch without a crossover cable ? "MDI by software"
> > >> thanks
> > >> mag
> On the cat side I think it is : set port auto-mdix enable. =A0Not sure
> on the native side.
Sorry, forgot the mod/port!
set port auto-mdix mod/port {enable | disable}
|
| Similar Threads | Posted | | Re: Connect a cisco catalyst 3524XL to a Cisco 6500 ? Auto-MDI or crossover cable | August 15, 2008, 7:32 am |
| Without Crossover Cable | September 25, 2006, 8:33 pm |
| Re: DB60 crossover cable | August 29, 2006, 10:30 pm |
| Connecting 3 switches to a fourth switch, each with its own crossover cable shuts down ports | March 29, 2007, 2:04 pm |
| Cisco 3524XL and 3508XL Throughput | November 10, 2004, 4:04 am |
| Point-to-point T1 with 2620XM and crossover cable | April 25, 2006, 4:59 pm |
| Cross over cable or straight to connect to 2811 from T1? | November 22, 2006, 4:59 pm |
| Cisco 1811 K9- VPN clients can connect, but can't connect or ping to computers | January 30, 2009, 4:30 pm |
| Catalyst 6500 help | October 9, 2007, 2:42 pm |
| catalyst 6500 power | February 20, 2006, 5:23 am |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML site map
> If i connect the C3524XL to a Cisco 6500 with a classic
> RJ45 cable, i don't have the link. If i use a crossover cable, i have the
> link.
> I think's that C3524/6500 don't have auto mdi.
> Anyone know if i can said by the cisco IOS that the port are connected
> to another switch without a crossover cable ? "MDI by software"
> thanks
> mag