If you were Registered and logged in, you could reply and use other advanced thread options
|
Posted by on March 5, 2008, 4:53 am
Hi all:
Today when I try to change the Gi1/0/1(routing port) on the fibre
module of 3750 into switchport by issuing the "switchport" command,
then assign it to a vlan, then I connect it to a fibre module on a
nortel layer2 switch. I found out there is no conectivity between the
3750 and the nortel switch. The status of the Gi1/0/1 is "not
connected". Is it because I cant do it on a fibre module?
Thank you
|
|
Posted by blue-birdy on March 5, 2008, 8:37 am
On Mar 5, 12:53=A0pm, xia...@xianli.net wrote:
> Hi all:
> Today when I try to change the Gi1/0/1(routing port) on the fibre
> module of 3750 into switchport by issuing the "switchport" command,
> then assign it to a vlan, then I connect it to a fibre module on a
> nortel layer2 switch. I found out there is no conectivity between the
> 3750 and the nortel switch. The status of the Gi1/0/1 is "not
> connected". Is it because I cant do it on a fibre module?
> Thank you
Hai,
wat Model of 3750 switch r u using?Gi1/0/1 is it fiber connection or
Ethernet?
B'cos i hav to deal with 3750 -24 10/100/1000 ethernet + 4 SFP.I have
couple of question reg that.Can u help me out?
Thanxs in advance.
|
|
Posted by on March 5, 2008, 8:31 pm
> On Mar 5, 12:53=A0pm, xia...@xianli.net wrote:
> > Hi all:
> > Today when I try to change the Gi1/0/1(routing port) on the fibre
> > module of 3750 into switchport by issuing the "switchport" command,
> > then assign it to a vlan, then I connect it to a fibre module on a
> > nortel layer2 switch. I found out there is no conectivity between the
> > 3750 and the nortel switch. The status of the Gi1/0/1 is "not
> > connected". Is it because I cant do it on a fibre module?
> > Thank you
> Hai,
> wat Model of 3750 switch r u using?Gi1/0/1 is it fiber connection or
> Ethernet?
> B'cos i hav to deal with 3750 -24 10/100/1000 ethernet + 4 SFP.I have
> couple of question reg that.Can u help me out?
> Thanxs in advance.
The switches I am working with is a 3750 48 10/100/1000 ethernet port
with 4 SFP module slots. If you have any porblems, just post it see if
I can help.
|
|
Posted by Maarten Carels on March 6, 2008, 3:32 am
>
> The switches I am working with is a 3750 48 10/100/1000 ethernet port
> with 4 SFP module slots. If you have any porblems, just post it see if
> I can help.
Then you certainly mean gi1/0/49.
The 48 copper ports are numbered 1 thru 48, and the SFP ones are the
next 4. Same on 24 port versions.
The numbers actually are present (very tiny) in the link LEDs of the
ports.
Hope this helps,
--maarten
|
|
Posted by on March 6, 2008, 7:03 am
On Mar 6, 11:32=A0am, maarten.car...@uva.nl (Maarten Carels) wrote:
> > The switches I am working with is a 3750 48 10/100/1000 ethernet port
> > with 4 SFP module slots. If you have any porblems, just post it see if
> > I can help.
> Then you certainly mean gi1/0/49.
> The 48 copper ports are numbered 1 thru 48, and the SFP ones are the
> next 4. Same on 24 port versions.
> The numbers actually are present (very tiny) in the link LEDs of the
> ports.
> Hope this helps,
> --maarten
helllo......
no ...u r wrong....if it is 48 ports 10/100/1000 ethernet ......with 4
sfp ports
the first SFP port will be Gi/0/1 apart from that 48 ports.i think it
is needed to check both ends of the switches for correct match....
like same kind of transceiver are used or not???
|
Page 1 of 2 1 2 > last >>
| Similar Threads | Posted | | Port mirroring in HP 2626-pwr 24 port switch | October 25, 2005, 2:01 am |
| change FTP port | April 27, 2007, 10:22 am |
| Change SSH Port | September 11, 2007, 2:18 pm |
| change pdm listening port | December 2, 2006, 6:16 am |
| Open port & change internal IP on PIX 501 | March 8, 2006, 2:19 pm |
| Flow Inside-outside change only destination port | April 20, 2005, 12:01 pm |
| Change Telnet Port Access to Router & Switches | August 10, 2005, 8:39 pm |
| Switch port | December 14, 2005, 12:09 am |
| switch port going up and down on specific NIC | October 12, 2006, 9:47 am |
| TCP/UDP port or protocol-based routing | February 6, 2006, 3:38 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML site map
> Today when I try to change the Gi1/0/1(routing port) on the fibre
> module of 3750 into switchport by issuing the "switchport" command,
> then assign it to a vlan, then I connect it to a fibre module on a
> nortel layer2 switch. I found out there is no conectivity between the
> 3750 and the nortel switch. The status of the Gi1/0/1 is "not
> connected". Is it because I cant do it on a fibre module?
> Thank you