|
Posted by Carneade on April 7, 2005, 7:20 pm
If you were Registered and logged in, you could reply and use other advanced thread options
As from the object I can't get my 1720 cisco router working
If I try to ping the outside I don't get any response (but to the inside
there is no problem)
my adsl line comes with a static ip, ipoa protocol, LLc encapsulation and
G.DMT
maybe a faulty hardware?
what follows is some commands I run to find clues...
Thanks in advance
gwnowin#show dsl int atm0
Alcatel 20150 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x1
Vendor ID: 'ALCB' 'ALCB'
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0x0F
Capacity Used: 20% 39%
Noise Margin: 34.0 dB 29.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 16.0 dB 10.0 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 329192 (0 spurious)
PHY Access Err: 0
Activations: 1
SW Version: 3.8129
FW Version: 0x1A04
Interleave Fast Interleave Fast
Speed (kbps): 1504 0 320 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0
DMT Bits Per Bin
00: 0 0 0 0 0 0 0 2 2 2 4 5 5 6 6 7
10: 7 7 6 6 6 6 5 6 5 5 4 3 4 3 0 0
20: 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2
30: 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 2
40: 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
50: 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
60: 4 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
70: 3 3 3 3 3 3 3 3 3 3 2 2 2 2 2 2
80: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
90: 2 2 2 2 2 2 2 2 2 2 3 3 3 2 2 2
A0: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
B0: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
C0: 2 2 2 2 2 2 2 2 2 2 2 2 2 3 2 3
D0: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
E0: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
F0: 2 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DSL: Training log buffer capability is not enabled
gwnowin#sh run
Building configuration...
Current configuration : 1643 bytes
!
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec localtime
service password-encryption
!
hostname gwnowin
!
logging buffered 4096 debugging
enable secret 5 xxxxxx/xxxxx/xxxxxxxxx
!
username xxxxxx privilege 15 password 7 xxxxxxxxxxxx
memory-size iomem 15
ip subnet-zero
!
!
ip domain name somewhere.net
ip name-server x1.y1.y1.t1
ip name-server x2.y2.y2.t2
!
ip audit notify log
ip audit po max-events 100
!
!
!
!
!
interface ATM0
ip address x.y.z.202 255.255.255.252
ip nat outside
no ip mroute-cache
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5snap
!
dsl operating-mode auto
!
interface Ethernet0
ip address 192.168.2.1 255.255.255.0
ip nat inside
no ip mroute-cache
half-duplex
!
interface FastEthernet0
ip address 192.168.1.1 255.255.255.0
ip nat inside
no ip mroute-cache
speed auto
full-duplex
!
interface Dialer0
no ip address
!
ip nat inside source list 10 interface ATM0 overload
ip nat inside source static tcp 192.168.1.2 80 interface ATM0 80
ip nat inside source static tcp 192.168.1.2 25 interface ATM0 25
ip nat inside source static tcp 192.168.1.2 443 interface ATM0 443
ip classless
ip route 0.0.0.0 0.0.0.0 x.y.z.201
no ip http server
!
!
access-list 10 permit 192.168.2.0 0.0.0.255
access-list 10 permit 192.168.1.0 0.0.0.255
access-list 60 permit 194.244.1.0 0.0.0.255
access-list 60 permit 192.168.1.0 0.0.0.255
access-list 60 permit 192.168.2.0 0.0.0.255
!
!
line con 0
line aux 0
line vty 0 4
access-class 60 in
login local
!
no scheduler allocate
end
gwnowin#show controllers atm 0
Interface ATM0 is up
Hardware is DSLSAR (with Alcatel ADSL Module)
IDB: 8161C798 Instance: 8162410C reg_dslsar:68030000 wic_regs:
68030080
PHY Inst:8161E5A0 Ser0Inst: 8160A738 Ser1Inst: 81613B9C us_bwidth:320
Slot: 0 Unit: 0 Subunit: 0 pkt Size: 4528
VCperVP: 256 max_vp: 256 max_vc: 65536 total vc: 1
rct_size:65536 vpivcibit:16 connTblVCI:8 vpi_bits: 8
vpvc_sel:3 enabled: 0 throttled: 0 cell drops: 0
Parallel reads to TCQ:0 tx count reset = 0, periodic safe start = 0
Serial idb(AAL5) output_qcount:0 max:40
Serial idb(RAW) output_qcount:0, max:40
WIC Register Value Notes
--------------- ---------- ----------
FPGA Dev ID (LB) 0x44 'D'
FPGA Dev ID (UB) 0x53 'S'
FPGA Revision 0x9F
WIC Config Reg 0x45 WIC / VIC select = WIC;
CTRLE addr bit 8 = 1;
OK LED on;
LOOPBACK LED off;
CD LED on;
WIC Config Reg2 0x03 Gen bus error on bad UNKNOWN DSL access
Int 0 Enable Reg 0x03 UNKNOWN DSL normal interrupt enabled
UNKNOWN DSL error interrupt enabled
DSLSAR Register Value Notes
--------------- ---------- ----------
sdram_refresh: 0x428FFFF
intr_event_reg: 0x80
intr_enable_reg: 0x13C FIFOF.FBQE.RQAF.RPQAF.TSQAF.
config: 0x660D0A20 UTOPIA.RXEN.RegulateXmit.RMCell.TXEN.
Rx Buffer size: 8192. RCT: Large, VPI Bits: 8.
status: 0x0
clkPerCell: 11983360
Pre-timer Count: 471
rcid_tableBase: 0x0
rct_base: 0x10000
tstBase1: 0x13C28 TST boot jump.
rawCellBase: 0x14300 (0/128) slots used.
rpq_base: 0x16000
tsqb(Tx Stat Q): 0x17000
fbq_base: 0x17880 (fbq_count: 128)
txChanQueue: 0x18000
rxBuffers: 0x30000
txBuffers: 0x130000
Lookup Error cnt: 0x0
Invalid Cell cnt: 0x0
SCCA Rx Errors: 0x0
SCCB Rx Errors: 0x0
Total Tx Count: 0x1
Total Rx Count: 0x4
Timer: 0x2E6360
DSLSAR Interrupts:0x0
Last Addr:0x12E14
VC QoS Summary
--------------
Active Configured Scheduled
Connections
VCD VPI/VCI COS PCR SCR/MCR COS PCR SCR/MCR
--- --------- -------- ------ ------- -------- ------- --------
1 8 /35 UBR 0 n/a UBR 320 n/a
Connections RX RX RX RX RX TX TX TX TX TX
TX
VCD VPI/ VCI AAL5 AAL2 RAW Chain Drop AAL5 AAL2 RAW TSI Drop
MISS
--- --- ----- ----- ----- ----- ----- ----- ----- ----- ----- ----- -----
0 0 /0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0
1 8 /35 2 2 0 0 0 0 0 0 0 0
0 1 1 0 0 0 0 0 0 0 0 0 0
TX Queues: |<-rcte->|<--TCD Contents->|<----- tcqTail TBD
Contents ----->|
VCD VPI/ VCI CtrlStat tcqTail tcqHead control bufAddr aal5Ctrl
cellHdr
--- --- ----- -------- -------- -------- -------- -------- -------- --------
1 8 /35 A0000 19010 10 11A0 173320 0 0
Summary Serial Device information:
AAL5:
Tx Interrupts = 1 , Tx BD Service Count = 1
Rx Interrupts = 2 , Rx BD Service Count = 2
RAW :
Tx Interrupts = 160 , Tx BD Service Count = 163
Rx Interrupts = 0 , Rx BD Service Count = 0
Detailed Serial Device information:
MPC860 SCC 1 statistics:
Serial IDB at 0x8160A738
DCE Unknown (13), clock rate 8000000
idb at 0x8160A738, driver data structure at 0x81612244
SCC Registers:
General [GSMR]=0x1980:0x00000030, Protocol-specific [PSMR]=0x8
Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x02
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E
Interrupt Registers:
Config [CICR]=0x00365F80, Pending [CIPR]=0x00004802
Mask [CIMR]=0x68200000, In-srv [CISR]=0x00000000
Command register [CR]=0x6C0
Port A [PADIR]=0x1100, [PAPAR]=0x9FCF
[PAODR]=0x0000, [PADAT]=0xF9FF
Port B [PBDIR]=0x0BC0F, [PBPAR]=0x0F00E
[PBODR]=0x00000, [PBDAT]=0x090FC
Port C [PCDIR]=0x000, [PCPAR]=0x000
[PCSO]=0x8E0, [PCDAT]=0xF3C, [PCINT]=0x000
Receive Ring
rmd(FF002430): status 9000 length 76 address 2A313C4
rmd(FF002438): status 9000 length 76 address 2A31A44
rmd(FF002440): status 9000 length 60C address 2914424
rmd(FF002448): status 9000 length 60C address 2933B64
rmd(FF002450): status 9000 length 60C address 29334E4
rmd(FF002458): status 9000 length 60C address 2932E64
rmd(FF002460): status 9000 length 60C address 29327E4
rmd(FF002468): status 9000 length 60C address 2932164
rmd(FF002470): status 9000 length 60C address 2931AE4
rmd(FF002478): status 9000 length 60C address 2931464
rmd(FF002480): status 9000 length 60C address 2930DE4
rmd(FF002488): status 9000 length 60C address 2930764
rmd(FF002490): status 9000 length 60C address 29300E4
rmd(FF002498): status 9000 length 60C address 292FA64
rmd(FF0024A0): status 9000 length 60C address 292F3E4
rmd(FF0024A8): status B000 length 60C address 292ED64
Transmit Ring
tmd(FF0024B0): status 5C00 length 48 address 2A7E768
tmd(FF0024B8): status 0 length 0 address 0
tmd(FF0024C0): status 0 length 0 address 0
tmd(FF0024C8): status 0 length 0 address 0
tmd(FF0024D0): status 0 length 0 address 0
tmd(FF0024D8): status 0 length 0 address 0
tmd(FF0024E0): status 0 length 0 address 0
tmd(FF0024E8): status 0 length 0 address 0
tmd(FF0024F0): status 0 length 0 address 0
tmd(FF0024F8): status 0 length 0 address 0
tmd(FF002500): status 0 length 0 address 0
tmd(FF002508): status 0 length 0 address 0
tmd(FF002510): status 0 length 0 address 0
tmd(FF002518): status 0 length 0 address 0
tmd(FF002520): status 0 length 0 address 0
tmd(FF002528): status 2000 length 0 address 0
tx_limited=0(16)
SCC GENERAL PARAMETER RAM (at 0xFF003C00)
Rx BD Base [RBASE]=0x2430, Fn Code [RFCR]=0x18
Tx BD Base [TBASE]=0x24B0, Fn Code [TFCR]=0x18
Max Rx Buff Len [MRBLR]=1548
Rx State [RSTATE]=0x18000000, BD Ptr [RBPTR]=0x2440
Tx State [TSTATE]=0x18001FD2, BD Ptr [TBPTR]=0x24B8
SCC Transparent PARAMETER RAM (at 0xFF003C30)
CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8
buffer size 20000
PowerQUICC SCC specific errors:
0 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts
Tx Interrupts = 1 , Tx BD Service Count = 1
Rx Interrupts = 2 , Rx BD Service Count = 2
Tx Errors: output_drops = 0 num_retransmissions = 0
Rx Errors: input_error = 0 giants = 0 input_frame = 0
input_abort = 0 input_crc = 0 input_overrun = 0
MPC860 SCC 4 statistics:
Serial IDB at 0x81613B9C
DCE Unknown (13), clock rate 8000000
idb at 0x81613B9C, driver data structure at 0x8161B6A8
SCC Registers:
General [GSMR]=0x1980:0x00000030, Protocol-specific [PSMR]=0x0
Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x02
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E
Interrupt Registers:
Config [CICR]=0x00365F80, Pending [CIPR]=0x00004802
Mask [CIMR]=0x68200000, In-srv [CISR]=0x00000000
Command register [CR]=0x6C0
Port A [PADIR]=0x1100, [PAPAR]=0x9FCF
[PAODR]=0x0000, [PADAT]=0x61FF
Port B [PBDIR]=0x0BC0F, [PBPAR]=0x0F00E
[PBODR]=0x00000, [PBDAT]=0x090FC
Port C [PCDIR]=0x000, [PCPAR]=0x000
[PCSO]=0x8E0, [PCDAT]=0xF3C, [PCINT]=0x000
Receive Ring
rmd(FF002730): status 9000 length 60C address 2A3E404
rmd(FF002738): status 9000 length 60C address 2A3EA84
rmd(FF002740): status 9000 length 60C address 2A3F104
rmd(FF002748): status 9000 length 60C address 2A3F784
rmd(FF002750): status 9000 length 60C address 2A3FE04
rmd(FF002758): status 9000 length 60C address 2A40484
rmd(FF002760): status 9000 length 60C address 2A40B04
rmd(FF002768): status 9000 length 60C address 2A41184
rmd(FF002770): status 9000 length 60C address 2A41804
rmd(FF002778): status 9000 length 60C address 292AC64
rmd(FF002780): status 9000 length 60C address 292A5E4
rmd(FF002788): status 9000 length 60C address 2929F64
rmd(FF002790): status 9000 length 60C address 29298E4
rmd(FF002798): status 9000 length 60C address 2929264
rmd(FF0027A0): status 9000 length 60C address 2928BE4
rmd(FF0027A8): status B000 length 60C address 2928564
Transmit Ring
tmd(FF0027B0): status 5C00 length 18 address 2A8D418
tmd(FF0027B8): status 5C00 length 1C address 2A8DAF8
tmd(FF0027C0): status 5C00 length C address 2A8E1D8
tmd(FF0027C8): status 5C00 length 1C address 2A87AB8
tmd(FF0027D0): status 5C00 length 600 address 2A88198
tmd(FF0027D8): status 5C00 length 600 address 2A88878
tmd(FF0027E0): status 5C00 length 22C address 2A88F58
tmd(FF0027E8): status 5C00 length 18 address 2A89638
tmd(FF0027F0): status 5C00 length 1C address 2A89D18
tmd(FF0027F8): status 5C00 length C address 2A8A3F8
tmd(FF002800): status 5C00 length 18 address 2A8AAD8
tmd(FF002808): status 5C00 length 6 address 2A8B1B8
tmd(FF002810): status 5C00 length C address 2A8B898
tmd(FF002818): status 5C00 length 600 address 2A8BF78
tmd(FF002820): status 5C00 length 600 address 2A8C658
tmd(FF002828): status 7C00 length 22C address 2A8CD38
tx_limite
SCC GENERAL PARAMETER RAM (at 0xFF003F00)
Rx BD Base [RBASE]=0x2730, Fn Code [RFCR]=0x18
Tx BD Base [TBASE]=0x27B0, Fn Code [TFCR]=0x18
Max Rx Buff Len [MRBLR]=1548
Rx State [RSTATE]=0x0, BD Ptr [RBPTR]=0x2730
Tx State [TSTATE]=0x18001FD2, BD Ptr [TBPTR]=0x27C8
SCC Transparent PARAMETER RAM (at 0xFF003F30)
CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8
buffer size 20000
PowerQUICC SCC specific errors:
0 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts
Tx Interrupts = 160 , Tx BD Service Count = 163
Rx Interrupts = 0 , Rx BD Service Count = 0
Tx Errors: output_drops = 160 num_retransmissions = 0
Rx Errors: input_error = 0 giants = 0 input_frame = 0
input_abort = 0 input_crc = 0 input_overrun = 0
gwnowin#show atm vc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells
Sts
0 1 8 35 PVC SNAP UBR 320
UP
gwnowin#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter
area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is x.y.z.201 to network 0.0.0.0
x.0.0.0/30 is subnetted, 1 subnets
C x.y.z.200 is directly connected, ATM0
S* 0.0.0.0/0 [1/0] via x.y.z.201
gwnowin#show atm map
gwnowin#
gwnowin#show interface atm0
ATM0 is up, line protocol is up
Hardware is DSLSAR (with Alcatel ADSL Module)
Internet address is x.y.z.202/30
MTU 4470 bytes, sub MTU 4470, BW 320 Kbit, DLY 6400 usec,
reliability 68/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
23 maximum active VCs, 256 VCs per VP, 1 current VCCs
VC idle disconnect time: 300 seconds
Last input 00:00:35, output 00:02:41, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
22 packets input, 1328 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
3 packets output, 84 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
|
| Similar Threads | Posted | | FastEthernet card not working in 12008 router | November 2, 2005, 6:36 pm |
| Config for cisco 1841 with one adsl for internet and one adsl for vpn | October 29, 2006, 3:31 am |
| cisco 4000 L3 card messages | January 4, 2005, 5:19 am |
| Cisco 2801 Router/E1 card | February 17, 2005, 4:59 am |
| HELP ! - Cisco 350 wireless LAN card and broadband | October 29, 2005, 10:49 pm |
| cisco wic vwic nm card questions | November 15, 2005, 11:42 am |
| Cisco 1700 With 1ENET WIC Card | January 7, 2006, 11:05 am |
| Cisco 5002 card question | August 30, 2006, 4:30 am |
| NIC Card Aggregation on Cisco Switch | October 30, 2006, 9:37 am |
| Cisco 1841 and SDSL WIC Card | January 16, 2008, 2:13 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML site map