|
Posted by Casa on April 4, 2008, 7:10 am
If you were Registered and logged in, you could reply and use other advanced thread options
Hi!
I changed compoactflash cards on one of our cisco 2801's power
connected trying to get a 512MB
card partitioned to 128MB to work, and when I Installed this 512MB
card, router dropped
suddenly to rommon. I Switched power off and tried to boot with
original Card but router finds
image and decompresses and loads it but hangs after "Installed image
archive" prompt.
I tried booting also with flashcards from other (working) 2801's
without success. I made sure
that config-register is 0x2102 and also tried with 0x2142, 0x2141 and
0x2101.
I tried to dowload new version of IOS to flash from Romboot with
tftpdnld command, but it does
not work as router has lost it's MAC address. Correct port (fa0/0) was
connected and link was
up. Any ideas how to fix this problem?
Best Regads
Marko Uusitalo
Router output below
*************************************************************
rommon 11 > tftpdnld
IP_ADDRESS: 192.168.1.27
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 192.168.1.254
TFTP_SERVER: 10.19.18.52
TFTP_FILE: c2801-ipbase-mz.124-1c.binget_mac_address():
Search T_IDPR
OM_MACADDR (0xc3) failed
Illegal MAC address.
************************************************************
Boot sequence:
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2004 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c2801 processor with 393216 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x1d2be3c
Self decompressing the image :
#################################################
################################################################################
################################################################################
################################################################################
##################################################### [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X00020000 Crypto module pools
0X00120000 VPM buffer pools
0X0012 0X00035000 Card in slot 1
0X0013 0X00035000 Card in slot 2
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 29011745 bytes to IO Memory.
PMem allocated: 362807296 bytes; IOMem allocated: 39845888 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version
12.4(9)T, R
ELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Sat 17-Jun-06 00:19 by prod_rel_team
Image text-base: 0x6008FCEC, data-base: 0x62F80000
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are
unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be
found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email
to
export@cisco.com.
Installed image archive
MACHINE JUST HANGS AFTER "Installed image Archive"
**********************************************************************
Boot sequence from Rommon
rommon 1 > dir flash:
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
Directory of flash:
2 30588892 -rw- c2801-advipservicesk9-mz.124-9.T.bin
rommon 2 > boot flash:c2801-advipservicesk9-mz.124-9.T.bin
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x1d2be3c
Self decompressing the image :
#################################################
################################################################################
################################################################################
################################################################################
##################################################### [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X00020000 Crypto module pools
0X00120000 VPM buffer pools
0X0012 0X00035000 Card in slot 1
0X0013 0X00035000 Card in slot 2
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 29011745 bytes to IO Memory.
PMem allocated: 362807296 bytes; IOMem allocated: 39845888 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version
12.4(9)T, R
ELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Sat 17-Jun-06 00:19 by prod_rel_team
Image text-base: 0x6008FCEC, data-base: 0x62F80000
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are
unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be
found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email
to
export@cisco.com.
Installed image archive
JUST HANG AFTER THIS
|
|
Posted by on May 27, 2008, 12:34 pm
If you were Registered and logged in, you could reply and use other advanced thread options
I am facing the similar problem. After I de-attached and attached the
CF card (with c1841-ipbase-mz.124-1c.bin) during the Cisco 1841 was
being booted, the router could not be booted properly with any WICs.
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2004 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 processor with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xd4a9a0
Self decompressing the image : ##################################=AD
###############
##################################=AD
##################################=AD ############
######## [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X0002 0X0001A800 Card in slot 0
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 7703097 bytes to IO Memory.
PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c),
RELEASE SO
FTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 25-Oct-05 17:10 by evmiller
Image text-base: 0x6007ECA0, data-base: 0x61480000
Port Statistics for unclassified packets is not turned on.
<----- Hang up here!!! ----->
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
If with CF card runing "c1841-advipservicesk9-mz.124-15.T3.bin", it
hangs up in the way similar to yours (.... Installed image
archive ....).
I tried to tftpdnld from rommon but it said "get_mac_address(): Search
T_IDPROM_MACADDR (0xc3) failed" and "Illegal MAC address."
If I swapped the unloadable CF cards to another Cisco 1841, it
worked. I pretty sure that the CF cards work correctly.
Did you fix the problem? If yes, in what way you got it fixed?
I just got a now rommon file "C1800_RM2.srec.123-8r.YH12" (IOS) and
see if it can help.
|
|
Posted by on May 28, 2008, 4:10 am
If you were Registered and logged in, you could reply and use other advanced thread options
> I am facing the similar problem. =A0After I de-attached and attached the
> CF card (with c1841-ipbase-mz.124-1c.bin) during the Cisco 1841 was
> being booted, the router could not be booted properly with any WICs.
I am pretty sure that I have read that you are not supposed to
insert or remove flash cards unless the router is OFF.
I of course ignored it but maybe there is a good reason for it.
I have not analysed the reports but consider - format the flash and
put new image on it?
|
| Similar Threads | Posted | | dialer profile problem with cisco 2801 | February 15, 2006, 12:58 pm |
| cisco 2801, ipsec problem with onboard accelerator | November 19, 2007, 10:21 pm |
| Cisco 2801 + Etherswitch + DSL + Cable modem config problem | April 2, 2005, 1:26 am |
| Cisco 2801 + Etherswitch + DSL + Cable modem config problem | April 2, 2005, 1:27 am |
| Strange problem when using PPTP VPN through Cisco PIX | October 21, 2005, 3:42 am |
| Cisco 2970 strange traffic problem - stumped cisco support | February 10, 2005, 9:19 am |
| 2801 two DSL multilink throughput problem.. | September 12, 2006, 6:03 am |
| boot of "cisco2-C1600" using boot helper "eprom:c1600-boot-r.111-10.AA" failed | June 9, 2007, 5:56 pm |
| Strange VPN problem | August 26, 2005, 6:36 pm |
| Strange problem 827 | April 13, 2007, 5:00 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML site map