RCA DCM315R

RCA DCM315R

NewsGroups | Search | Tools
 comp.dcom.modems.cable  Post an article  get this group's latest topics as an RSS feed add this group's latest topics to your My MSN content add this group's latest topics to your My Yahoo content  add this group's latest topics to your Google content  YahooMyWeb Yahoo!  Google Google  Windows Live Favorites Windows Live  del.icio.us del.icio.us  digg digg  Add to Netscape Netscape
Subject Author Date
RCA DCM315R JustMe 09-18-2005
Posted by JustMe on September 24, 2005, 5:26 pm
If you were  Registered and logged in, you could reply and use other advanced thread options



>
>> says...
>>> The most common point of failure on many of the RCA models is the
>>> power plug. Off-hand I can't recall when they stopped using them, but
>>> many of the 200's, including the 245, used a Molex-type plug. The
>>> jacks were not braced enough by the case, and a lot of stress was put
>>> on the boards they were connected to. It doesn't take much movement
>>> to break the connection, and cause the modems to go offline.
>>
>> I've also read a few reports that the power supplies were a bit
>> underpowered for some. My DM315 is rated for 9-12V@200mA. The supply
>> is the minimum 9V@200mA. Some had connection problems, mainly
>> establishing the uplink (when it's doing the 3-bar flash), that was
>> fixed by using a higher voltage/current supply. I checked mine UNDER
>> LOAD (poked through the insulation while powering the modem), and it
>> registered around 11V or so if I remember right, so my supply seems
>> OK.
>>
>
> True. My DCM245 came with a 9v 800mA block transformer. A few months
> later, a box from Comcast arrived on my doorstep, containing a new
> transformer, rated at 11v 800mA. A small brochure said that "a limited
> number of power supplies may experience weakened performance over time",
> but there was no safety risk. "Thompson and Comcast are proactively
> implementing a Power Supply Replacement program in order to prevent
> interruption of your Internet service due to this circumstance".
>
> I never swapped out the old transformer, but saved it just in case.
>
> Bruce

That's interesting. I work around the corner from the store I purchased my
DCM315. I bought it during lunch and took it back to the shop and examined
it. I noted that it appeared to have been used although the seal was intact.
The power cube was rated 12 v. I took it back and got another one. When I
opened it up, I noted the power cube was rated at 9v, 800ma. I looked for
the specs in the book and on the modem case and didn't find any. I wonder
what the power requirements really are?




Network Magic 20% Off NMEASY coupon code spring banner 468x60
Posted by Andrew Rossmann on September 25, 2005, 8:13 am
If you were  Registered and logged in, you could reply and use other advanced thread options


says...
> That's interesting. I work around the corner from the store I purchased my
> DCM315. I bought it during lunch and took it back to the shop and examined
> it. I noted that it appeared to have been used although the seal was intact.
> The power cube was rated 12 v. I took it back and got another one. When I
> opened it up, I noted the power cube was rated at 9v, 800ma. I looked for
> the specs in the book and on the modem case and didn't find any. I wonder
> what the power requirements really are?

Right under the power socket on the modem itself, it's printed, along
with a little icon showing the polarity. I just posted a correction that
mine lists 9-12V@800mA (not the 200mA I posted originally.)

The supply I tested with was a nice RadioShack one that uses a high-
efficiency switching supply (it's much lighter in weight since it
doesn't have a big transformer.)

--
If there is a no_junk in my address, please REMOVE it before replying!
All junk mail senders will be prosecuted to the fullest extent of the
law!!
http://home.att.net/~andyross


Posted by Andrew Rossmann on September 25, 2005, 8:06 am
If you were  Registered and logged in, you could reply and use other advanced thread options


andysnewsreply@no_junk.comcast.net says...
> says...
> > The most common point of failure on many of the RCA models is the power
> > plug. Off-hand I can't recall when they stopped using them, but many of the
> > 200's, including the 245, used a Molex-type plug. The jacks were not braced
> > enough by the case, and a lot of stress was put on the boards they were
> > connected to. It doesn't take much movement to break the connection, and
> > cause the modems to go offline.
>
> I've also read a few reports that the power supplies were a bit
> underpowered for some. My DM315 is rated for 9-12V@200mA. The supply is
> the minimum 9V@200mA. Some had connection problems, mainly establishing
> the uplink (when it's doing the 3-bar flash), that was fixed by using a
> higher voltage/current supply. I checked mine UNDER LOAD (poked through
> the insulation while powering the modem), and it registered around 11V
> or so if I remember right, so my supply seems OK.

Minor correction. It should be 800mA, not 200mA. It's very hard to
read that simple raised plastic lettering from where the modem is
stuffed!! I also double-checked the supply, and it's a generic 9V/800mA
brick.

--
If there is a no_junk in my address, please REMOVE it before replying!
All junk mail senders will be prosecuted to the fullest extent of the
law!!
http://home.att.net/~andyross



other useful resources:
The Federal Communications Commission (FCC)
Telecommunications Industry Association
Electronic and Software Security Products and Services
International Telecommunication Union

Custom CGI Perl and PHP programming by 1-Script.com

Contact Us | Privacy Policy
The site map in XML format XML site map