|
Posted by Paul on December 22, 2004, 3:13 pm
If you were Registered and logged in, you could reply and use other advanced thread options
I have a 1750 router here with a VIC-2FXO-M1 card. Upon bootup, with
the card in any slot, I received:
00:00:05: %PQUICC-1-UNKNOWN_WIC: PQUICC(0), WIC card has an unknown ID
of 0x2B
I went through the Cisco tool to select the IOS I needed and installed
c1700-sv3y-mz.122-27.bin so I'm now on:
IOS (tm) C1700 Software (C1700-SV3Y-M), Version 12.2(27), RELEASE
SOFTWARE (fc3)
I still get the "unknown ID" error even though the tool at
http://tools.cisco.com/Support/Fusion/FusionHome.do said it was
supported.
Am I using the wrong IOS? I reset the thing to factory defaults and
reloaded to find the same error.
Router>show version
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV3Y-M), Version 12.2(27), RELEASE
SOFTWARE (fc3)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Tue 02-Nov-04 18:36 by kellmill
Image text-base: 0x800080E0, data-base: 0x80B2B198
ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Router uptime is 8 minutes
System returned to ROM by reload
System image file is "flash:c1700-sv3y-mz.122-27.bin"
cisco 1750 (MPC860) processor (revision 0x601) with 36864K/12288K bytes
of memory.
Processor board ID JAD05041B3X (3666672781), with hardware revision
3097
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
|
|
Posted by Paul on December 23, 2004, 7:58 am
If you were Registered and logged in, you could reply and use other advanced thread options
Some helpful person directed me to the link below. Apparently I need
IOS 12.2(2)XJ
http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml
It's not on http://www.cisco.com/kobayashi/sw-center/sw-ios.shtml - the
IOS download page though. Is there a different download page I'm not
seeing?
|
|
Posted by Anthony on December 23, 2004, 11:32 pm
If you were Registered and logged in, you could reply and use other advanced thread options
Try 12.2(15)T and later versions of IOS. I would go to the latest T
release if I were you, but the support for that card should be there in
15T. Let me know if this works, if not I will try and investigate it a
little further.
Thanks
Anthony
|
|
Posted by Paul on December 28, 2004, 7:34 am
If you were Registered and logged in, you could reply and use other advanced thread options
memory for that it seems - I get this error:
TFTP flash copy: Error, image size (9372712) larger than flash
(8388608).
|
|
Posted by Paul on December 28, 2004, 8:30 am
If you were Registered and logged in, you could reply and use other advanced thread options
related to voip on the 1750 needs 16MB of flash mem. I guess I need to
upgrade the memory as a "show version" tells me I only have 8MB:
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-Y-M), Version 12.3(12), RELEASE SOFTWARE
(fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 29-Nov-04 22:22 by kellythw
Image text-base: 0x8000816C, data-base: 0x80A512FC
ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-Y-M), Version 12.3(12), RELEASE SOFTWARE
(fc3)
PSTN-TEST uptime is 27 minutes
System returned to ROM by reload
System image file is "flash:c1700-y-mz.123-12.bin"
cisco 1750 (MPC860T) processor (revision 0x601) with 41276K/7876K bytes
of memory.
Processor board ID JAD05041B3X (3666672781), with hardware revision
3097
MPC860T processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
(The failed upgrade to 12.2(15)T left me with ROMmon only so I put the
standard IP version of 12.3(12) on.
|
| Similar Threads | Posted | | A non-Cisco router, BDCOM 1700 Router Series | June 28, 2008, 4:27 am |
| Cisco 1700 Router | July 25, 2008, 8:00 am |
| Very strange ftp problems through 1700 router. | August 14, 2005, 2:12 pm |
| how to stop denial of service in a 1700 router | September 2, 2005, 3:09 pm |
| 1700 Router - creating a dot1q VLAN subinterface | July 5, 2007, 9:49 pm |
| cant ping when adding secondary ip to 1 fastethernet interface on 1700 router | August 17, 2005, 12:14 pm |
| configuration of a router Cisco 1700 on ADSL max of a wide-area network | February 10, 2006, 4:49 am |
| Error on router to router GRE / IPSec Tunnel | March 18, 2005, 10:32 am |
| error on 2800 series router | April 30, 2006, 10:02 am |
| Which is the OID for the error CRC on interface router cisco | August 29, 2007, 4:37 pm |
|
|
Yahoo! 
Google 
Windows Live 
del.icio.us 
digg 
Netscape 
XML site map